OBJECTIVE: To modify and dynamically adjust the pause time between past the windshield wiper in tim

[TUTORIAL] - Timer windshield wiper regulvel Corsa Club Brazil - Index of Frum -> Tutorials Author Message LMM1973 Super :: :: Age: 45 Joined: Monday, August 2, 2010 Posts : 53 Scoring: 0 LOCATION: Porto Alegre - RS Posted: Friday 20th 2012f July 2012 04:49:02 PM Subject: champlain [TUTORIAL] - Timer windshield wiper regulve
OBJECTIVE: To modify and dynamically adjust the pause time between past the windshield wiper in timed estgio. Source: taken and adapted from the page [url]http://www.clubedagraxa.com.br/blog/instalacao-de-temporizador-para-o-limpador-de-parabrisas-no-troller-tutorial/ preserving, thus, appropriate crditos. Material needed: - soldering iron 30w; - Tin solder; - Maximum of 2 meters of wire same size of the original timer wire; - The potencimetro shown in the pictures; - Tape OR terminals champlain "faston" with their capes; champlain - A Knob for potencimetro. - Key philips; - A resistor 1K ohm; - Termocontrtil spaghetti. Step 1: Remove champlain the rel shown in the figure:
Figure 2: The rel timer itself, with its GM number. Step 2: Open the rel with aid of two small screwdrivers or it believes appropriate as a tool. Step 3: With the open rel, dessolde the resistor 2,9K Ohms and weld in his place 1K ohm resistor.
Figure 3: The rel timer open j with the resistor to be exchanged. Unfortunately, I found datasheet IC "TY93029A". In the tutorial cited as source of this tutorial, the CI in question one ATMEL controller with known datasheet. The function of TY93029A the same. However, pinning both the (best in inventing fashion and leave it quiet). The resistor exchanged the "I" terminal champlain rel, is responsible for the timed estgio.
Figure 4: The REL with the indication pin "I". Step 4: Turn off the car battery. champlain Step 5: Remove the cover from the core of ignioea lower coverage direction of column. This last, by unscrewing the three philips champlain screws and slide a bit the top cover to gain access to plug that controls the windscreen wiper.
Figure 5: Coverage of crumb ignioea lower coverage direoj column removed indicating the location of the three screws to be removed. Step 6: Choose a convenient place to put the potencimetro. I chose the cover of the button that controls the height of the headlights, since my car is in this option and the previous owner already had a rough hole in place, probably to put an alarm LED.
Figure 7: The chosen coverage to accommodate the potencimetro because it already had a rough hole. Step 7: I have installed on the roof of potencimetro botoe warped 90 degrees the end of it in order to fit into the panel without scraping at all.
Figure 10: direction of the column with the j plug disconnected. champlain Step 9: In the plug, release the terminal which has the black wire with yellow list or cut this wire. I opted for solt you plug as Figure 12 shows. So, avoid using electrical tape and break, around the installation 100% reversible without sequelae in the original wiring if ever I decide to uninstall everything and leave as it was originally. I think the day I sell the car, the new owner has the right to receive the car without enjambraes caused by accessories or electrical resources in the documents that have been removed. But it will of each. Solder one end of the black wire with yellow list in the terminal "A" or "C" potencimetro using a piece of wire. See figure 12. Now, another solder champlain wire piece at the other end of the yellow wire with black list (where it is written "to the terminal 'A' or 'C' of the potencimetro") champlain and its other end in Terminal "B" potencimetro.
Figure 15: Who got the THING NO. Considerations: When estgio timer activated, the wiper operates continuously, but with the rel clicking. Then, as the potencimetro turned by the driver, the pause time between a passage and one wiper increases. In my car, when est potencimetro in half of its working stroke, j cleaner gets a bygone per minute. This suggests that the chosen potencimetro has a "range" (interval minimum value at omximo) of too broad resistance. But pro d spent in damaging the operation. I suggest the choice of a potencimetro of "range" low. The resistor 1K Ohm proved very low value because in the course of the button champlain early, the cleaner works like velociade 1 (the timer). This suggests that it would be more appropriate a resistor of 1.1 Ohms or 1,2K. Thus, the cleaner would start the timer estgio about half-second pause between a past and over. Binding of potencimetro could have been made direct to pin "I" of the housing of the relay behind the fusveis box. This would dispense with the removal of c